Shogun-motorsports Honda CBR600F4_F4I (99-06) Frame Slider Manuel d'utilisateur télécharger pdf

Honda CBR600F4/F4I (99-06) Frame Slider

Installation Instructions

Part Numbers: 750-3209, 750-3200 & 850-3200

MADE IN THE USA!

Carefully read instructions in their entirety before the install

Professional installation is recommended. Always use proper safety measures during the install of this

product. Do not try to install this product without proper tools, recently calibrated torque wrench,

correct torque specifications from factory service manual, safety goggles and gloves. The motorcycle

must be in a fixed secure position before the install process begins. DO NOT remove both engine studs

at the same time. Shogun is not responsible for any part of your motorcycle for any reason. Precisely

measure location of cut and if in doubt at any point please call us before the install process has begun.

Replacement Parts List: Left Side Components (as if you were sitting on the bike)

QTY Price each Part Numbers Descriptions

1 $20.00 99-FS-750-3209-L Black Left Side Puck

1 $20.00 99-FS-750-3200-L White Left Side Puck

1 $25.00 99-FS-850-3200-L Chrome Left Side Puck

1 $3.50 99-HB-SH10125090 Socket Cap 10 X 1.25 X 90 Main Engine Stud

Replacement Parts List: Right Side Components (as if you were sitting on the bike)

1 $20.00 99-FS-750-3209-R Black Right Side Puck

1 $20.00 99-FS-750-3200-R White Right Side Puck

1 $25.00 99-FS-850-3200-R Chrome Right Side Puck

1 $3.50 99-HB-SH101250110 Socket Cap 10 X 1.25 X 110 Main Engine Stud

Frame Sliders: Left frame slider is longer than right.

Installation Steps:

1. Some photos in this section are used for illustration examples only. It is up to you how you

decide to cut your motorcycles bodywork to accept the frame slider there are many different

ways customers go through this process. Shogun is not responsible for any part of your

motorcycle for any reason. Precisely measure location of cut and if in doubt at any point please

call us before the install process has begun. Professional installation is recommended. Always

use proper safety measures during the install of this product. Do not try to install this product

without proper tools, recently calibrated torque wrench, correct torque specifications from

factory service manual, safety goggles and gloves.

2. Body Prep. Use masking tape to completely mask off the area on the body where you will be

working. We usually will tape off approximately 6 to 8 inches around the though hole area and

any other edges that could get bumped or scratched while working. Tip: In some locations you

may want to double up the thickness of the masking take to give extra protection.

1 2 3 4

Installation Instructions 1

Résumé du contenu

Page 1 - Installation Instructions

Honda CBR600F4/F4I (99-06) Frame Slider Installation Instructions Part Numbers: 750-3209, 750-3200 & 850-3200 MADE IN THE USA! Carefully read inst

Page 2

3. Locating and cutting the body. This is a simple illustration of how most of us install the product here. It takes a bit longer but our end resul

Page 3

6. Using a small drill ¼ inch or so drill a pilot hole in the body from the inside out. Remount bodywork and double check the hole location with the

Page 4

9. Remove left side bolt. Mount left side puck with (99-HB-SH10125090) Socket Cap 10 X 1.25 X 90 Main Engine Stud and torque down. 10. Remove ri

Commentaires sur ces manuels

Pas de commentaire

Shogun-motorsports Honda CBR600F4_F4I (99-06) Frame Slider Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les motocyclettes Shogun-motorsports Honda CBR600F4_F4I (99-06) Frame Slider. Shogun Motorsports Honda CBR600F4_F4I (99-06) Frame Slider User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour les motocyclettes Shogun-motorsports Honda CBR600F4_F4I (99-06) Frame Slider